Speedy Senior - 4-Wheel Setup Electric Mobility Scooters

Speedy Senior^® 4G Quick-Start Setup Guide

Available at www.SpeedySenior.com/4G-Setup.htm

Printer-Friendly PDF Version

Troubleshooting

I. Assembly Tools Needed

A. 6mm Allen wrench

B. 12mm wrench

C. Adjustable wrench

6mm Allen Wrench 12mm Wrench Adjustable Wrench

II. Assembly

A. Check the Inventory

1. User Manual

2. Seat Post

3. Seat Bottom

4. Seat Backrest

5. Two Armrests

6. Basket

7. Battery Charger

8. Hardware Kit

a. Two Seat Post adjustment Detent Pins (1 spare)

b. Two Access Keys (1 spare)

c. Two Backrest Bolt, Sleeve, and Nuts

d. Two Armrest Adjustment Knobs

e. Two Anti-tip Wheels

User Manual Seat Post Seat Bottom Seat Backrest

Armrests Basket Battery Charger

Detent Pins Keys Backrest Bolts Armrest Knobs

II. Assembly (continued)

B. Check Electrical Connections

1. Batteries - Dual Plug Connection

2. Motor - Single Plug Connection

Battery Connections Motor Harness Connection

C. Seat Post Installation

1. Use Highest Position for taller riders

2. Use Lower Positions for heavier riders or shorter riders

3. Make sure Detent Pin slides through both holes

D. Seat Distance Adjustment (optional)

1. Three Seat Distances to Increase or Decrease the angle of your knees

2. Scooter is shipped at farthest distance from the steering tiller, to give the rider more legroom.

3. Unscrew Allen bolts from Seat Bottom with 6mm Allen wrench

3. Move Seat frame to desired position. Longer Allen bolts are for the front, taller holes.

4. If Allen bolt will not screw in, check the nut position inside the seat by unbuckling rear

snaps, lifting up padding, and relocating the nut into the correct hole.

Seat Post Installed Seat Bottom Hole Locations

Seat Distance Allen Screws Inside Seat Retaining Nuts

II. Assembly (continued)

E. Seat Bottom Installation

1. Place seat axis into Seat Post

2. Rotate by lifting side Lever

3. Remove the Seat by Lifting slightly, then activate the lever

Lever Free to Rotate Lever Locked

F. Seat Bottom & Backrest Assembly

1. Position Backrest

2. Place Bolt & Sleeve into holes, then tighten the Locknut

3. Do Not Over tighten - Sleeve keeps assembly tight, while allowing Backrest to fold down

Insert Bolt and Sleeve Tighten Nut on Outside

G. Armrest Installation

1. Position Armrests through tubing on Seat Bottom

2. Screw in Armrest knobs in desired setting

3. Adjust Armrest Height by turning bolt located underneath armrest

Armrest Adjustment Knob Armrest Height Adjuster Screw

II. Assembly (continued)

H. Front Basket Installation

1. Locate Basket Bracket on front steering tiller

2. Hang Basket

I. Anti-Tip Wheel Installation

1. Insert a washer onto the screw, and slide through the anti-tip wheel.

2. Place another washer on the opposite side of the anti-tip wheel, and slide through the frame facing outwards.

3. Place the last washer on the screw, and tighten the nut, still allowing the wheel to spin freely.

Basket Bracket Basket Installed Anti-Tip Wheel

J. Rearview Mirror Installation

1. The scooter is shipped with a bolt in the handlebars, in place of the mirrors, to prevent damage during shipment.

2. Simply remove the bolt, and thread the correct mirror into each side of the handlebars.

3. When the mirror is inserted, tighten the chrome nut, and adjust for the best viewing angle.

III. Operation

A. Charging the Batteries - Always Fully Charge Prior to First Use

1. Charge on Board - Plug Charger into Center Port

2. Charge Off Board Remotely - Plug Charger Adapter into each Battery

B. Headlight Switch

1. Located on side of Dashboard

2. Turns on only with Key inserted

Central Charging Port Front Light Switch

IV. Disassembly and Transporting

A. Disassembly

1. Lock Steering Tiller, Remove Seat and Basket. You may wish to remove the Armrests

first to make the Seat lighter.

2. Remove Batteries, unplug Motor electrical connection

3. Rotate Rear Section away, and lift front section to separate

4. Fold Down Steering Tiller, and the scooter is now ready for Transporting

Unlatching the Toggle Strap and Motor Harness Toggle Strap Released

Rotate Rear Section and Lift Front Section to Separate

B. Assembly

1. Align Rear Section pins, with Slots on front section.

2. Rotate into place, and Lock Toggle Buckle

3. Plug in Motor electrical connection

4. Install batteries, Seat Post, and Seat & Armrest

5. Unfold Steering Tiller, Install Basket, and Unlock Tiller

Align Frame Pins Tiller Lock

V. Troubleshooting

Issue: Scooter Dashboard indicates the scooter is working, but it does not move.

1. Check the following steps, in this order, even if you have already done so:

a. Unplug the dashboard key, and both the left & right batteries.

b. Unplug the motor connector, at the right-rear corner of the battery compartment.

c. Move the freewheel lever, which is located on the rear section of the scooter with a yellow handle, into

freewheel position, so that you can easily move the scooter by hand.

d. Firmly move the freewheel lever back into drive mode until it locks into position, so that you can not move

the scooter by hand.

e. Press the circuit breaker reset button several times, located between the batteries, to make sure it has

not tripped.

f. Inspect the motor plug to make sure the 2 red prongs and the 2 black prongs are fully extended, and plug in

the motor connection firmly until it locks in place.

g. Plug in the left & right batteries firmly.

h. Turn the speed control to the slowest setting, and then just slightly faster by 1/8 of a turn.

i. Plug in the key to the dashboard, and check the following:

i) scooter is fully charged

ii) red Status light is lit up

iii) battery indicator gauge shows a full charge

iv) operate the headlight switch to make sure the headlight is working

v) operate the horn to make sure it is working

j. Check the operation of the scooter by pressing the throttle lever forward or reverse.

i) If the scooter still does not move, listen for a clicking sound coming from the rear section of the

scooter, where the transaxle is located.

ii) If you hear a clicking sound, this is the brakes releasing, and the transaxle needs to be replaced.

iii) If you can not hear a sound, the electrical controller is faulty. Call Speedy Senior at 440-452-2213

to obtain further assistance.

Issue: Scooter Dashboard does not indicate power unless the battery charger is plugged in.

2. Check the following steps, in this order, even if you have already done so:

a. Unplug the battery charger from the charging connection on the scooter.

b. Unplug both batteries from the scooter, remove the key, and turn the headlight off.

c. Plug in both batteries firmly to the scooter.

d. Insert the key. Turn on the headlight. You should now see the headlight is on, and the battery indicator should read a full charge.

i) if the battery meter is not full, remove the key and plug in the battery charger for 12 hours.

ii) if the battery meter shows nothing at all, and the headlight does not work, plug in the battery charger. If the battery meter now shows full and the headlight works, you have a bad battery. Replace both batteries from either a local auto parts store or local supplier. Speedy Senior can also supply batteries fro $75, which includes both batteries, new wiring, and includes shipping as well. Send $75 by PayPal to info@speedysenior.com, with the subject as "Replacement 4G Batteries."

Contact Us for Live Support - Online Instant Messaging

MSN AOL Skype Yahoo! Google

info@speedysenior.com SpeedySeniorCo SpeedySenior SpeedySenior info@speedysenior.com

Home | Privacy Policy | Terms & Conditions | Contact Us | Warranty